Page 4 of 7

Re: Phunkie Project Portafold

Posted: Sat, 24 Mar 2012, 9:02 pm
by phunkie hiboy
Right, didn’t take too long to work out what was happening and put a plan into action, but first, on taking off the fittings and drilling out the pop rivets, the left rear supporting steel for the roof lifting handle exploded. It had rotted out on the upper edge, and is no good anymore.
picture 411_(640_x_480).jpg
So the old one was cut out.
picture 412_(640_x_480).jpg
And a new one fabricated from aluminium.
picture 415_(640_x_480).jpg
Then, after cleaning the old mounting surface, this was installed using Sikaflex to bond it to the roof.
picture 416_(640_x_480).jpg
Then a couple of layers of laminate to clean up the inside.
picture 430_(640_x_480).jpg
There was a small repair to do at the front edge where he roof pivots on the little aluminium sliders.
picture 417_(640_x_480).jpg
Just set up a straight support outside, ground away part of the edge and laminated the repair from the inside. The outside will be addressed when we do the repairs on the outside.
picture 418_(640_x_480).jpg
Now, on to the “sagging” right side of the roof. The problem seems to have been caused by a weakness on the inside edge of the right hand “fin” allowing the roof to “flatten” out.
With the roof turned upside down on the base, this allows the roof to take its proper shape, weight was added to the “sag” area, expanded aluminium was cut to shape as a support to aid laminating.
picture 408_(640_x_480).jpg
Both inner portions of the “fins” were laminated over and the front portion as well. This gives us a Portafold roof on the outside and an Ansfold roof on the inside, but it has worked to give a non saggy roof.
picture 409_(640_x_480).jpg
picture 410_(640_x_480).jpg
To help to make this modification stronger but still light, holes were drilled into the fins from inside and the void filled with expanding foam.
picture 432_(640_x_480).jpg
Now to make a smoother/good looking roof surface, in side, it was sanded off and a complete one piece sheet of fibreglass cloth was bonded to it. This hasn’t added too much weight to the roof, as cloth is quite light compared to chopped strand mat.
picture 433_(640_x_480).jpg
picture 435_(640_x_480).jpg
As today has been very warm, the glass has been “going off” pretty quickly , so by the time I’m back on it again it’ll be fully hard and will only require a light sanding before painting it with the white top coat. :wave:

Re: Phunkie Project Portafold

Posted: Sat, 24 Mar 2012, 10:31 pm
by vauxhallbitz
Great minds think alike! I did exactly the same to my roof it was so much easier filling in the fins when I applied the foam headlining, never thought about the expanding foam though! You can see it on "first outing after rebuild thread" in the owners gallery.

Re: Phunkie Project Portafold

Posted: Tue, 27 Mar 2012, 6:48 pm
by 70sfreak
Superb , keep the pictures coming Chris !

Re: Phunkie Project Portafold

Posted: Wed, 28 Mar 2012, 6:02 pm
by phunkie hiboy
70sfreak wrote:Superb , keep the pictures coming Chris !
Thanks for that, Steve. Probably going to do a big push over easter, the dagster's at Allards now having some pipes made.

Re: Phunkie Project Portafold

Posted: Fri, 06 Apr 2012, 7:31 pm
by Ambubird
phunkie hiboy wrote:Sorry, forgot to put in a couple of pictures, then it wouldn't let me. Anyway here they are, after sanding the seal guides ready for primer.
1.jpg
And a picture of how the unfinished "U" section mouldings are supplied.
2.jpg
Thank you.
Does anyone know what type of seals go in these guides? Mine are missing.
(Sorry to hijack your thread Phunkie, keep the pics coming, we've started on ours at long last :crazy: )

Re: Phunkie Project Portafold

Posted: Sat, 07 Apr 2012, 3:02 pm
by phunkie hiboy
Hey Debbie,
Don't worry about hijacking the thread for information. Whether it's "right" or not, we have found (and are using) a rubber cord. It's black closed cell rubber, 16mm in diameter. it will need to be glued into the guide somehow, obviously it's easy for us 'cos it can be fitted before the side walls are installed. We got it from a company in Reading called Halls Rubber company, don't think they've got a web site but they do have a phone (0118 958 0535) and they are really helpful.
1.jpg

Re: Phunkie Project Portafold

Posted: Sat, 07 Apr 2012, 5:09 pm
by phunkie hiboy
So, yes, the cloth laminate has now hardened and the edge has been trimmed and sanded. The inside has now been lightly sanded and painted over with white top coat.
1.jpg
Whilst that was drying, I made the trim panel for the lower rear door, from a piece of 3mm exterior ply. It was marked out for the trim clip positions and drilled through into the door. A trial fit was made using “clico’s”, now ready to drill holes full size in readiness for the clips.
picture 449_(640_x_480).jpg
picture 450_(640_x_480).jpg
picture 451_(640_x_480).jpg
Back to the main body, after removing the chassis, the body was turned over and the final external repairs carried out. The whole of the underside, up to the join, was then sanded. We’re doing in sections because it’s easier for us, to do it that way.
picture 445_(640_x_480).jpg
It was then sprayed with primer. Firstly with a Max Mayer epoxy 2 pack primer. This adheres to the fibreglass and makes a good base for the Max Mayer 2 pack primer/filler, which covers all the pinholes in the surface of the fibreglass. This is not going to be a “perfect” job, the preparation for that would take hundreds of hours, but it will be to a presentable standard.
picture 452_(640_x_480).jpg
picture 456_(640_x_480).jpg
picture 459_(640_x_480).jpg
picture 460_(640_x_480).jpg
I’ll leave that for a few days, or so, to harden, then next week end we’ll turn it back over and finish the top area, above the join line.
Be back soon :wave:

Re: Phunkie Project Portafold

Posted: Sun, 08 Apr 2012, 8:50 pm
by Ambubird
Thanks for that info.

(When will the spending end?! :crazy: )

Re: Phunkie Project Portafold

Posted: Sat, 14 Apr 2012, 7:50 pm
by phunkie hiboy
Now the primer has hardened, the body has been turned over.
Before we go any further, the two front support/roof axis bracket fixing area needs to be addressed. Problem is that, the wooden block that the brackets are screwed into are not touching the fibreglass inside the body, hence all the cracks around the mount.
picture 472_(640_x_480).jpg
As soon as the screws are tightened, the glass is pulled in cracking the gel coat. So, just made up some packing “shims” out of 3mm exterior ply and tapped them in between the wooden block and the outer skin.
picture 471_(640_x_480).jpg
Now, having sanded all the upper part of the body, all the storage bin holes are masked up and the area painted firstly with epoxy primer and then hi build primer.
picture 475_(640_x_480).jpg
As we are going to add top coat colour this time, a guide coat of black is added.
picture 476_(640_x_480).jpg
This then sanded, untill all the black is gone. This makes sure all the marks and imperfections have been sanded out. The bins are masked up again.
picture 477_(640_x_480).jpg
The colour is now spayed on. The colour we’ve chosen for this is a period colour from the 60s & 70s, BMC “Old English White”.
picture 478_(640_x_480).jpg
After the paint has tacked off, the whole thing is demasked.
picture 481_(640_x_480).jpg
picture 482_(640_x_480).jpg
Need to let it harden off completely, then we can start to fit it up with lights and stuff :thumbup:

Re: Phunkie Project Portafold

Posted: Sat, 28 Apr 2012, 8:00 pm
by phunkie hiboy
Right, whilst the main body is hardening we’ll paint the lower rear door, hinges and the hook up flap.
Hook up flap first, as it’s plastic we need to have some adhesion and flexability so firstly a coat of adhesion promoter then a couple of light coats of etch primer. This ensures that the textured finish is not lost.
picture 496_(640_x_480).jpg
Then a couple of coats of “Old English White” to finish.
picture 512_(640_x_480).jpg
So onto the lower door and hinges. It was decided to paint the hinges body colour, firstly ‘cos they just wouldn’t look right in black and in the early advertising and the video they are shown as a light colour, so either body colour or white. Same prep as the body, one coat of epoxy and two/three coats of high build primer all sanded down and painted with three coats of colour.
picture 513_(640_x_480).jpg
picture 514_(640_x_480).jpg
After painting the main part of hook up unit, where the hinges are, by hand (brush) it was fitted to the body and the flap fitted to that using it’s pivot pins.
picture 519_(640_x_480).jpg
picture 520_(640_x_480).jpg
To fit the lower rear door hinges, it was decided to use rubber gaskets. As these can’t be bought, they had to be made. A quite simple job, a piece of wood with two holes drilled for the bolts, some thin flat rubber (old truck inner tube) and a sharp craft knife. Cut two holes in the rubber, install hinge through the rubber into the holes in the wood and cut around the hinge.
picture 511_(640_x_480).jpg
Right we are now ready to fit up the rear end. Fit half the hinges to the main body and the other halves to the lower door. As the hinges had been badly fitted in the first place and this made the lower door too low, an easy fix to raise the door would be to make two oblong brass balls to fit between the two hinge halves. As luck would have it some of the Land Rover hinge balls are a larger diameter, which just meant turning down the middle diameter to make them oblong. The door was then assembled to the body and secured.
The original style new handle was fitted with stainless steel screws.
The refurbished original number plate light was re-positioned to the centre of the lower door.
Number plate fixings were made from a couple of import lower number plate fixings and a couple of Rivnuts for the top mounts.
The rear lights chosen were the same lights that we used on our Airstream camping trailer and are of the type used on an Austin A55. They were obtained from http://www.vintagemotorspares.com for 22 quid each. These were fitted and connected. Also the reflective triangles that came with the caravan originally were secured with SS screws. And now it all looks like this...
picture 538_(640_x_480).jpg
Now we’ve made a start on the sides. The left side has had a couple of small repairs in the gel coat done and sanded. Following what went before, one coat of epoxy and a couple of coats of high build ……….
picture 531_(640_x_480).jpg
A guide coat ……………
picture 532_(640_x_480).jpg
All sanded down and then three coats of colour …………….
picture 535_(640_x_480).jpg
I thought that while that was starting to dry off, I’d install the hinges ready to fit the whole side to the body once it was completely dry.
picture 536_(640_x_480).jpg
picture 537_(640_x_480).jpg
Until next time then …………………….. :wave: